What did you do to your AT4 today?

[Brembo6point2]

New badges

 

AT4 Forum Fav 👍

Ironclad EXO Motor Impact Gloves - Grab a set through Amazon!

[Brembo6point2]

Can’t let a good badge go to waste

And here’s just a beuty shot I took

 

[Brembo6point2]

Installed some Rough Country Eboards, figured I’d give them a shot. I figured it’d be a 1-2 hour job and let’s just say it took me a lot longer than that lol, a lot of stress removing so many trim panels to install steps. Would probably go with obd like the amps on my old truck next time. But all said and done I am impressed I gotta say, the dual motor on each side is noticeable over my amps I had. Only drawback I’d say is they are very instant, when you open the door they come down with a vengeance and as soon as the door closes I hope nobody’s limbs get in the way haha, overall very satisfied especially for the price point. Professional installation is recommended unless u are good at not breaking trim panels that cost more than a piece of plastic should(I am not one of those people).

 

[Aftonoutdoorsman]

Hyper dipped the badges

 

[zeeya]

Added back up lighting. Used the road shock lights from harbor freight. Spliced them into the cargo lights, which is accessible behind the tail light housing. No problem for both of them. Did the same thing on my 2017 and never had any issues.

Attached are the before and after views using the backup camera. Night and day…View attachment 5553View attachment 5554View attachment 5555View attachment 5554View attachment 5554View attachment 5555

Great job, I have utilized the VLED brand in the past and now I have it on my AT4. The Ram had the nice 12" screen, but the reverse lights sucked. This is the VLED on my GMC. I wired it into my 7 pin plug. Some people buy the plug that goes in between the 7 pin bumper mount and the actual harness behind the bumper. I did the cheap splice job. This is the 3rd truck I have used them on and they work great.

LP-R LICENSE PLATE REVERSE LIGHT BAR

Output 2500lm measured output (8X brighter than a standard reverse light) Output 13X 5W Cree XT-E 5500K chips Lens UV resistant polycarbonate Waterproof Potted and sealed for IP68 rating Material All aluminum CNC machined construction Finish Satin black exterior grade powder coating...

www.vleds.com

 

[Aftonoutdoorsman]

Great job, I have utilized the VLED brand in the past and now I have it on my AT4. The Ram had the nice 12" screen, but the reverse lights sucked. This is the VLED on my GMC. I wired it into my 7 pin plug. Some people buy the plug that goes in between the 7 pin bumper mount and the actual harness behind the bumper. I did the cheap splice job. This is the 3rd truck I have used them on and they work great.

LP-R LICENSE PLATE REVERSE LIGHT BAR

Output 2500lm measured output (8X brighter than a standard reverse light) Output 13X 5W Cree XT-E 5500K chips Lens UV resistant polycarbonate Waterproof Potted and sealed for IP68 rating Material All aluminum CNC machined construction Finish Satin black exterior grade powder coating...

www.vleds.com

That looks great, probably would have gone that route if I knew it existed. Would have wanted to see those pics though before dropping the cash.

 

[jconner00]

Hyper dipped the badges

i see that you're also afraid of the small at4 on the front grille!

I have hyper dipped my rear GMC and Sierra logos and the tail pipes, and replaced the rear and side AT4 emblems with the OEM black and red, but i'm deathly afraid to tackle the front GMC and to replace that AT4 badge in the grille i hear is a nightmare.

 

[Aftonoutdoorsman]

Honestly i didn’t see it until I was already spraying. I’ll do it and let you know how bad it wa

 

[Cocoabean]

I’m about to hyperdip (next weekend I hope). Does the front GMC emblem come off easily? That would help a ton.

 

[Wakinvol]

I’m about to hyperdip (next weekend I hope). Does the front GMC emblem come off easily? That would help a ton.

I’d have to say no. I got mine off but it wasn’t easy. It would be easy with grill removal, but I didn’t want to take the fender flares loose and mess with all that. I reached in from the backside (through the vents-that came loose and I had to put back) and finally got it out. Broke the chrome one in the process. Long story short I did it but it wasn’t the funnest mod I’ve done.

 

[Cocoabean]

I’d have to say no. I got mine off but it wasn’t easy. It would be easy with grill removal, but I didn’t want to take the fender flares loose and mess with all that. I reached in from the backside (through the vents-that came loose and I had to put back) and finally got it out. Broke the chrome one in the process. Long story short I did it but it wasn’t the funnest mod I’ve done. View attachment 5836

View attachment 5837

Damn, I was hoping I could go in from the top to remove just the GMC emblem. The “easy” mods are never so easy.

 

[Wakinvol]

Damn, I was hoping I could go in from the top to remove just the GMC emblem. The “easy” mods are never so easy.

That was my hope…but it’s NOT the case.

 

[jconner00]

That was my hope…but it’s NOT the case.

was there no way to get a tool behind there and just snap the clips off and let the old one fall out? Any pics of the back of the old emblem to give me an idea of what it's attached like? Thanks man!

 

[Wakinvol]

was there no way to get a tool behind there and just snap the clips off and let the old one fall out? Any pics of the back of the old emblem to give me an idea of what it's attached like? Thanks man!

It might could be done with a flat screwdriver but it’s not real easy. I didn’t take pics of the part but from memory there are 3 clips on the top and 2/3 on the bottom. The new emblem is a good reference for location.

 

[Brembo6point2]

Upgraded my factory gauge cluster to the Denali one last night.