What did you do to your AT4 today?

[Johnv76]

The amber or the fog light in the OEM fog light location?

The amber Baja Design lights are off road light, however i use them during heavy snows and rains. Also off roading too lol. The fog lights in the OEM location, those are SAE, from Diode Dynamics.

 

AT4 Forum Fav 👍

Precision Upfit Micro3 ATM ADD-A-Circuit Fuse Tap Link - Grab one through Amazon!

[ivey_usmc]

Out in Sedona AZ this week for vacation so I had to search for the best place to take some photos

What front bumper is that?

 

[Clarkely]

Installed the passenger side Boost sequential amber fender lights

 

[Jake3point0]

Installed my tire sensors in my camper tires, and synced them to my truck. All works well, I'm pleased. Especially for $40. Started playing with my obd2 reader and obdfusion. The data geek in me was nerding out over all the potential data. I can see myself spending hours customizing guages and screens. I'll do some searching, but if anyone has a thread or master list of good pid's, I'm all ears.

 

[SamSterlingAT4]

What front bumper is that?

Im running DV8 off roads front and rear bumpers. Visit DV8offroad.com

 

[Youngrodder]

I finalized the install of a 12k winch and battery box for my open car trailer. I tried to keep everything as tidy as possible.

 

[W1NGMAN]

Paint corrected and ceramic coated. Since it was a 2,500 mile demo (The old bosses car line) that saw the dealerships car wash frequently so it needed some minor correcting. Came out great !

 

[hdrolling]

Little video showing cold start with the MRT exhaust valve simulator plugged into the active exhaust valve. It keeps the valve open in all drive modes and somehow opens the valve more to make the active exhaust louder. $55 on ebay, little cheaper than a muffler swap if your looking for just a little louder.

 

[Clarkely]

Added venom drl sequential adapter, will post photos in that thread and my mod thread

 

[NorCalSixTwo]

Finally received my illuminated emblem!

 

[Johnv76]

Desert Does It molle panel installed today. Awesome quality, and design. Just quickly installed it, not really setup. However will work for now till I iron it all out and set it up to my liking.

 

[SmittysAT4]

Fronts done, much easier than I was expected. Half the stock bolts were barely a little over hand tight.

View attachment 26198

View attachment 26199
View attachment 26200
View attachment 26201
View attachment 26202

Looks great! What lift and what specs on those 20" wheels?

 

[hdrolling]

Looks great! What lift and what specs on those 20" wheels?

In the front Bilstein 6112 set to the highest notch and 5160s on the rear, and then ready lift UCAs. These raised the front about 1 1/2".
Wheels are :
BRINK B204 INSURGENT
Size: 20x9 Finish: SMOKE MACHINED TITANIUM Offset: 0
Nitto Ridge Grappler
Size: 285/60/20

​

 

[SmittysAT4]

In the front Bilstein 6112 set to the highest notch and 5160s on the rear, and then ready lift UCAs. These raised the front about 1 1/2".
Wheels are :
BRINK B204 INSURGENT
Size: 20x9 Finish: SMOKE MACHINED TITANIUM Offset: 0
Nitto Ridge Grappler
Size: 285/60/20

View attachment 28823

​

Looks Soooo GOOD! where are ya'll getting the Black n Red AT4 badges and those RED and Black GMC badges? I need those ASAP as well....

 

[AT4guy013]

Installed the Venom Amber DRL switchback harness. Should have come this way from the factory! Also installed the Autostop eliminator.