What did you do to your AT4 today?

[RugbyRef]

With all of the great advice on here, I had a set of Maxxis Razr A/T's installed on all four corners. I ended up going with 295/70R18. @Cocoabean and others were right...no rubbing, no scrubbing, no trimming. I have not installed my 1.5" leveling kit yet and I was worried I would see some interference with the front air dam or mudflaps, but...nope...they fit perfectly!

Again...thanks for the tips guys (too many to acknowledge)! Love this forum!

 

AT4 Forum Fav 👍

VIAIR 400P/40045 Automatic Portable Compressor 150 PSI/2.30 CFM - Grab one through Amazon!

[TxMarine832]

Purchased it.

2021 with 18,8XX miles.
Lift, 20" Fuel rims wrapped in 35x12.50 Nitto Edge Grapplers.

Probably my first upgrade will be to powered drop steps.View attachment 2217

What lift kit did you go with? It sits perfectly!

 

[Dobes11]

With all of the great advice on here, I had a set of Maxxis Razr A/T's installed on all four corners. I ended up going with 295/70R18. @Cocoabean and others were right...no rubbing, no scrubbing, no trimming. I have not installed my 1.5" leveling kit yet and I was worried I would see some interference with the front air dam or mudflaps, but...nope...they fit perfectly!

Again...thanks for the tips guys (too many to acknowledge)! Love this forum!

Do you have any pictures you can share? I'm about to put 285/65/20's on stock carbon pro wheels and stock suspension and am a bit worried about rub. Looks like the setup is about the same diameter as yours with a slightly narrower tire. Any help would be much appreciated!

 

[RugbyRef]

Do you have any pictures you can share? I'm about to put 285/65/20's on stock carbon pro wheels and stock suspension and am a bit worried about rub. Looks like the setup is about the same diameter as yours with a slightly narrower tire. Any help would be much appreciated!

You bet! I'll post some up later today.

 

[RugbyRef]

@Dobes11 (and everyone else) - here's a link to a "tire calculator" that I use extensively when trying to envision how a particular size tire/rim combo will work with my vehicles. It's pretty self-explanatory, but you will have to enter some parameters. You'll see what I mean...

https://www.wheel-size.com/

When you get to the home page, look up in the dark grey bar and and click on "Tire Calculator".

 

[Dobes11]

@Dobes11 (and everyone else) - here's a link to a "tire calculator" that I use extensively when trying to envision how a particular size tire/rim combo will work with my vehicles. It's pretty self-explanatory, but you will have to enter some parameters. You'll see what I mean...

https://www.wheel-size.com/

When you get to the home page, look up in the dark grey bar and and click on "Tire Calculator".

Thank you!

 

[Big Kahuna]

wash and wax and I made this fun video

 

[ProfezzorX]

Installed my Brembos today... I think it turned out well. Now I need to break them in.

 

[Rle312]

Yes that is what I have 285/70/18 Toyo AT3 No Level/No Rub

Looks great, I'm looking to get that exact tire for my AT4 (when it arrives) I wonder if they would fit on AT4 too not just AT4X.

 

[Rle312]

With all of the great advice on here, I had a set of Maxxis Razr A/T's installed on all four corners. I ended up going with 295/70R18. @Cocoabean and others were right...no rubbing, no scrubbing, no trimming. I have not installed my 1.5" leveling kit yet and I was worried I would see some interference with the front air dam or mudflaps, but...nope...they fit perfectly!

Again...thanks for the tips guys (too many to acknowledge)! Love this forum!

Do you have the AT4 or AT4X?

 

[Sinisterj]

Looks great, I'm looking to get that exact tire for my AT4 (when it arrives) I wonder if they would fit on AT4 too not just AT4X.

It should fit on an at4 only difference between the two is shocks from a height standpoint

 

[RugbyRef]

Do you have the AT4 or AT4X?

I have the AT4X.

 

[BB2022]

buffed and waxed with products below +Foam applicators to apply and microfiber towels to buff. Total time about an hour with wax drying time. total work time 20 ish minutes.

Scratch and Swirl Remover
Extreme Top Coat Sealant

Thanks for tip. Was trying to find a good product to remove unwanted scratches and swirls

 

[BB2022]

Check out this guy on Instagram if you like custom badging.

https://instagram.com/0fx2gv?igshid=YmMyMTA2M2Y= View attachment 2158

Can you send a link to where to purchase ? Did I miss it. Thanks.

 

[Dobes11]

Put new 285/65/20 Mickey Thompson Baja Boss's on and trimmed a bit to ensure no rubbing.