Duramaximus
Well-known member
Looks good man!
Lambo’s 2021 GMC Sierra 1500 AT4 build
- Thread starter LamboTexas
- Start date
Quick question- How does that 3D printed gas cap attach? I had a few brain cells of an idea to put a quick disconnect, for an air compressor, where the def tank filler would be (I have the 6.2 as well). I could modify that cap to hold the QD, but only if it’s secure enough. I’d have to look in to compressors that can be controlled by a switch or remote (on/off/psi) to make it easier if the compressor was mounted under my hood.
EDIT: You can ignore this question. I just went and looked and It’s just a very soft plastic where the def filler would be, I never paid attention lol. I will just have to use those few brain cells to attempt to engineer something!
EDIT: You can ignore this question. I just went and looked and It’s just a very soft plastic where the def filler would be, I never paid attention lol. I will just have to use those few brain cells to attempt to engineer something!
Last edited:
LamboTexas
Well-known member
Not a dumb question at all! No I did not remove the overhead console or headliner. I just routed the cables between windshield and headliner. Tucked in easily in headliner. Then ran cables down the pillars. I did remove pillars to do this but that was as simple as it gets. Then took cable for rear camera and ran through the drain hole in drivers floorboard and underneath the truck to the rear. It was really a simple install that could easily be removed for any reason. I have a thread on here that describes the install. Worst part of install was the trucks spray on undercoating on the carriage. That stuff is like molasses!This is a dumb question I’m sure but I’m guessing you had to pull the console down and the headliner? And this does record? Throw a brick at me if it’s a stupid question
Last edited:
LamboTexas
Well-known member
Thread 'VanTop H612T'This is a dumb question I’m sure but I’m guessing you had to pull the console down and the headliner? And this does record? Throw a brick at me if it’s a stupid question
https://www.at4forum.com/threads/vantop-h612t.177/
LamboTexas
Well-known member
Instead of saying “console” I should’ve said headliner! I’ll edit the post
Pb82 Ronin
Well-known member
How hard was the headliner to remove?
EDIT: Sorry, just read that you didn't remove it. I Englesh good...I promus.
EDIT: Sorry, just read that you didn't remove it. I Englesh good...I promus.
Last edited:
I have the exact same truck and was thinking about going with the ranch hand midnight replacement bumper. What's your thoughts on that bumper? Trying to find pic of one but no luck. Thanks
Regular Cab Duallies
"RCD"
Last edited:
Oldschool
Active member
I really like this full replacement and it looks awesome other than how wide it sticks out around the lights- still searching for one that doesn’t stick out so far! I think this width problem could be resolved ( looks wise ) with spending $8000 on a high quality lift, tires, extended flares , wheels and 35x13.50 tires
that’s a lot to spend to make it match the truck on the front but Not out of the question JMHO
that’s a lot to spend to make it match the truck on the front but Not out of the question JMHO
Regular Cab Duallies
"RCD"
But it sure would be sweet!
Here are some other front bumper options if you decide you want something else:
Aftermarket Bumpers!
Anyone have aftermarket bumpers on their AT4? If not, which ones do you like? Lets see some pictures! I hate having different front and rear bumper brands but these were the best options IMO. Here are the ones I like: HD AT4 Front: Ranch Hand Midnight. $1699 for either...
www.at4forum.com
Is there a winch which will fit on a 2020 1500 AT4 without having to change the original bumper?
I have a 2020 AT4 1500 diesel and I want to put a winch on it, but I really don't want to change anything else about the front end. Is that possible?
www.at4forum.com
And this sure would help your headlight problem
: Widebody (or even prerunner) AT4?
Anyone want to widebody their AT4? It would look amazing IMO, way better than stock! It is a 4 inch bulge with a 2 inch rise, made by FiberwerX. They are offered in fiberglass and carbon fiber, and made for the 5.5FT bed. While were on this topic, some long travel suspension would go really well...
www.at4forum.com
Oldschool
Active member
I like the wide body route but I wouldn’t want them painted! I’d go for the Carbon fiber in Matte Carbon fiber!
That little piece of 2” pipe bumper totally takes away from the looks of the truck and Scares the HeCk out of me! I don’t think insurance would cover a front end collision with it!
That little piece of 2” pipe bumper totally takes away from the looks of the truck and Scares the HeCk out of me! I don’t think insurance would cover a front end collision with it!
Regular Cab Duallies
"RCD"
Heck yeah! I meant widebody with the RH Midnight
I'm not a very big fan of that tube bumper either.Thanks so much RCD! It looks awesome!
Regular Cab Duallies
"RCD"
Sure, not a problem!
GMC AT4 Forum Photos
GMC AT4 Forum Photos
