Just installed Cognito Elite 3” Level and HATE…

[RiverHopper]

…that I didn’t do it sooner. The ride quality of my stock 2024 HD AT4 was very nice for a heavy duty truck, but this level kit, paired with the Elka 2.5 shocks, takes the ride to a next level. I haven’t taken it off-road yet, but i suspect when adjusted correctly, it will take the beast of a truck to new heights. I was debating going with the 4” lift, the wife argued it was too much…glad she won that one. This level is insane.

 

AT4 Forum Fav 👍

Precision Upfit Micro3 ATM ADD-A-Circuit Fuse Tap Link - Grab one through Amazon!

[s4cruiser]

Pics or it didn’t happen!!

 

[reb0957]

Yes, Please post pics! I have been researching this to a level of stupidity! My truck rides like crap. My local mechanic says do what ever you want to do to the truck now. Then test it out and make changes.

 

[yzf1999]

post some pics of your new setup please

 

[RiverHopper]

Sorry for the suspense...photos below. Debating on getting 37" when these 35" wear out, would love to hear your thoughts.
Because of the delay, I added a bonus snap of some bed mods I'm also happy about. The BuiltRightIndustry Molle Panel are f'n AWESOME! Enjoy!

 

[reb0957]

35s on factory wheels! Are you using a spacer? Did you take before and after measurements? Looks damn good!

 

[Cocoabean]

Sorry for the suspense...photos below. Debating on getting 37" when these 35" wear out, would love to hear your thoughts.
Because of the delay, I added a bonus snap of some bed mods I'm also happy about. The BuiltRightIndustry Molle Panel are f'n AWESOME! Enjoy!
View attachment 5791
View attachment 5792
View attachment 5796
View attachment 5797
View attachment 5793View attachment 5794View attachment 5795

37's look amazing on this truck. Do it. Do it now!

 

[RiverHopper]

35s on factory wheels! Are you using a spacer? Did you take before and after measurements? Looks damn good!

Factory all the way. No spacers, No rubbing. I did not take measurements. Full disclosure…they are 285/65/20…so 34.6”.

 

[RiverHopper]

37's look amazing on this truck. Do it. Do it now!

You’re bad for my wallet. Thanks for the encouragement!

 

[reb0957]

Do you feel that it could handle another 1.2" of tire width? Height of 35x12.5x20 is same height, just 1.1" wider!

 

[RiverHopper]

Do you feel that it could handle another 1.2" of tire width? Height of 35x12.5x20 is same height, just 1.1" wider!

I don’t. The gap between inner tire and the ball joint of the UCA is about .5”.

I think you’ll need a spacer.

I’m not a mechanic, but I did sleep in a holiday inn.

 

[nabatron]

This is the kit I want to go with on mine but probably just go the fox setup. The 35s look tiny to me haha. Not sure if I want to go 37 route though.

 

[RiverHopper]

This is the kit I want to go with on mine but probably just go the fox setup. The 35s look tiny to me haha. Not sure if I want to go 37 route though.

Depending on which Fox kit you go with, I have heard that they ride a bit stiff. If you can stomach the extra $$$, i def go with an adjustable shock…King, Fox 2.5 DSC. Of course I fully endorse the Elkas.

Yes…37” would look pimp. If i go that route, i think I’d also get them wrapped around 18” Method Bead Grip 701 HDs.

 

[yzf1999]

Did you specifically get this kit so the front would be higher than the back?

 

[RiverHopper]

Nope...just to get it leveled. There is still a slight rake from front to back. But i can see how it may "look" like the front is higher. It could be because the front wheel well is cut higher than the back, I also think the hood might be slightly taller.